IQ Builders

Drywall takeoff: sheets, tape and screws from a plan

A drywall takeoff turns a floor plan into square feet of board, then into sheets, tape, screws and joint compound. The math is simple. Most mistakes come from a wall face that wasn't counted, a ceiling that was missed, or a ceiling height that changes partway through the house.

What you need from the plans

The floor plan gives you wall lengths. Sections, elevations or room notes give you ceiling heights. The finish schedule or wall types tell you which board goes where: regular board, moisture-resistant board in wet areas, and type X wherever the plans call for a fire-rated wall or ceiling. Mark every place the board type or the ceiling height changes before you measure anything.

Step 1: Measure the walls and count both faces

Measure every wall run on the floor plan. Exterior walls get board on the inside face only. Interior partitions get board on both faces, so count their length twice. Closets are easy to miss: their walls are short, but a house has a lot of them.

Wall board = total length of board faces × ceiling height. Take a 40 × 30 ft single-story house with 140 linear ft of exterior wall, 180 linear ft of interior partitions and 8 ft ceilings: (140 + 2 × 180) × 8 = 4,000 sq ft of wall board.

Step 2: Add the ceilings

A flat ceiling has the same area as the floor under it, so the example house adds 1,200 sq ft of ceiling board, for 5,200 sq ft in total. For a sloped or vaulted ceiling, take the true length from the section, or multiply the flat area by the slope factor for its pitch.

Step 3: Decide how you handle openings

Many estimators don't deduct standard doors and windows. The board is usually hung across the opening and cut out, so most of that piece is waste anyway. They deduct only large openings such as garage doors, wide cased openings and window walls. Whichever rule you pick, use it on every job so your numbers stay comparable.

Step 4: Convert square feet to sheets

A 4 × 8 sheet covers 32 sq ft and a 4 × 12 sheet covers 48 sq ft. Divide the board area by the sheet size, then add waste: 10% is a common starting point, more for small, cut-up rooms. For the example house, 5,200 ÷ 48 = 108.3 sheets of 4 × 12, and with 10% waste you'd order 120. Price the sheet size your crew actually hangs: longer sheets mean fewer butt joints but are harder to carry in and hang.

Step 5: Tape, screws and joint compound

Gypsum board makers publish material rates per 1,000 sq ft of board. The Gypsum Construction Handbook gives about 370 linear ft of joint tape, and about 1,000 screws for a single layer on framing 16 in. on center (about 850 at 24 in.). For the example house's 5,200 sq ft, that's about 1,900 ft of tape and 5,200 screws.

Joint compound depends on the product and the finish level. The bag or bucket lists its coverage, so use that figure, and allow more for a Level 5 finish, which adds a skim coat over the whole surface.

Step 6: Labor

Hanging and finishing are usually priced per square foot of board or per sheet. Use rates from your own past jobs, and add for high walls, stairwells and lots of small rooms.

Check it before it goes out

Doing it in IQ Builders

Upload the PDF plans and set the scale on each sheet by clicking two points on a known dimension. Measure wall runs with the linear tool, then multiply by the ceiling height, and measure ceilings with the area tool. The quantities go into the estimate's line items, so nothing gets retyped. Manual measurement is part of the Ultimate plan.

The AI Takeoffs add-on, available on any paid plan, makes a first pass: it reads the printed scale and dimensions and lists quantities by trade for you to check. Estimates and invoices are free on the Starter plan. See pricing.

Quick reference

ItemRule of thumb
Wall boardwall length × ceiling height; interior partitions count twice (both faces)
Ceiling boardfloor area for flat ceilings
Sheetsboard area ÷ 32 (4 × 8) or ÷ 48 (4 × 12), plus about 10% waste
Joint tapeabout 370 linear ft per 1,000 sq ft of board
Screwsabout 1,000 per 1,000 sq ft (single layer, framing 16 in. on center)
Joint compoundthe coverage printed on the product, more for a Level 5 finish

New to measuring from PDFs? Start with how to do a construction takeoff from a PDF plan. Prefer a spreadsheet? Use the free estimate template.

More trade guides: painting, framing, electrical.

Try IQ Builders free